Iscar Offers A Completely New Family Of Slitting Cutters Applying Tang-Grip Technology And The Durability Of Sumo Tec Grades


Auto Insurance

Iscar currently offers a family of high-performance slitting tools that combine the convenience and security of Tang-Grip clamping with the increased sturdiness of the new Sumo Tec insert grades.

The perception, already demonstrated successful in Tang-Grip parting tools, has now been spread to slitting cutters. In the patented Tang-Grip clamping system, inserts are press-fit into their pockets accompanying a specialized hand tool, and are held tightly in place without having the need for clamps, upper jaws or set screws that can weaken the insert and disrupt chip flow. The pocket configuration uses cutting forces to retain the insert seated solidly in position, removing any risk of insert pull-out. The Tang-Grip clamping system also fosters increased accurate slitting cuts plus increased pocket and insert life.

Iscar's Sumo Tec insert grades showcase a specific post-coating treatment which considerably increases tool life and constancy.

Launched in late '07, the completely new Sumo Tec treatment flattens the insert's coated surface to eliminate microscopic stress raisers, lessen heat and friction and enhance chip flow. The result is improved toughness and opposition to chipping and built-up edge, all leading to enhanced tool life. The golden-colored flank on Sumo Tec inserts aides wear detection. Size for size, Tangslit cutters give more teeth than Iscar's SGSF cutters, enabling higher feed rates.

Their superior rigidity leads to straighter, increased accurate cuts and diminished vibration even in large-diameter cutters. The revolutionary Tangslit TGSF cutters come in 100 to 160 mm diameters, 3 and 4 mm widths and can accept the exact same variety of inserts as Tang-Grip parting tools. Additional sizes will be added.

Existing Sumo Tec grades for Tangslit cutters include:
IC808, with a tough submicron substrate below a Sumo Tec TiAlN PVD coating, offering extraordinary resistance to impact loads and built-up edge. This grade is endorsed for slitting heat resistant alloys, austenitic stainless steel, hard alloys and carbon steel.

IC830, presenting greater toughness for heavier parting and grooving involving interrupted cuts. It is suited for any stainless steel and high temperature alloys.

IC908, a hard, fine-grain substrate with extraordinary chipping resistance, joined with a new Sumo Tec TiAlN PVD coating. It is perfect for nodular or grey cast iron.

IC928 and 928A, PVD TiAlN-coated tough grades fitting for stainless steel, high temperature alloys and other alloy steels. These grades are also suggested for interrupted cuts and heavy operations.

Each Tangslit and Tang-Grip inserts are available in J- or C-type chipformer geometries from Iscar.

Iscar Recently Made Public A Variety Of New Lines To Enlarge Their Family Of Milling Tools
Iscar recently released a new family of High Speed Milling adjustable endmills and facemills that will improve milling of aluminum, non-metallics, cast iron and hardened steel. This should prove especially useful in the automotive and aerospace industries.

Some Of Improvements In Carbide Inserts By Iscar
Iscar is introducing a new unique milling system with tangential, clamped, butterfly-shaped LNKX carbide inserts. The butterfly-shaped insert has significant advantages compared to the current flat, square shapes. The new geometry has more cutting edges, positive rake face, reduced cutting forces resulting in higher performance.

New Tools And Carbide Insert Configurations From Iscar To Better The Machining Procedure
Iscar is introducing Penta 34 carbide inserts with a new PB chipformer. The PB chipformer features a single cavity with a positive rake, neutral shoulder angle, and a honed edge. It is actually a C-type chipformer with a different frontal edge.

Various Advancements Have Increased Iscar's Line Of Indexable Endmills For Elevated Productivity
Helido-Upfeed 04 Two years ago Iscar introduced the extremely efficient H600 indexable endmill line, based on conceptually new Helido-Upfeed double sided inserts with 6 cutting edges. The first insert launched was the H600 WXCU 0806..., which was designed for milling cutters in the diameter range of 50 to 125 mm.

Some Of Changes In Carbide Inserts Provided By Iscar Through The Last Decade
Iscar is announcing a brand new unique milling system that includes tangential, clamped, butterfly-shaped LNKX carbide inserts. The butterfly-shaped insert has meaningful advantages compared to the current flat, square shapes. The new geometry has more cutting edges, positive rake face, decreased cutting forces resulting in better performance.

Push Pull Testing For Construction Industry With Calibrated Measuring Instruments. Mechanical Load Testing Methods For On Site Documentation To Testing Requirements.
Push Pull Testing for the Railway industry for proof of reliable anchor fixings. Calibrated push pull force gauges are used for stress load testing along with tensile strength pull testing procedures. Proof of load testing undertaken, measured, recorded in a reliable and standard way to BS5080 Part 1 standards.

The Truth On The Graduate Jobs Obtainable In Europe.
Even if there is no formal education in medical school, new graduates planning to pursue such graduate careers can undergo training to cover the basics in health care to learn the non-specialized functions of the medical doctor.

Try To Get Automotive Manufacturing Jobs.
There is no point in denying that workers serving in the automotive industry are also suffering from the economic recession that everybody is experiencing world wide.

Search

 

More Articles

Associated Sites